My bike
-
- Scary biscuits
- Posts: 147
- Joined: Sat Sep 19, 2009 4:23 am
- Current Ride: 2007 Yamaha R.1
- Location: Aberdeen
My bike
I have decided to get a paint jobby done on my R.6. Mike Stuart is doing the job and I have decided to go for a Rossi Rep, but red rather than blue. See below
I got the wheels off today, so I popped in past Mr Sillets and got the rubber removed then dropped the wheels off at Finesse to get powdercoated white. I should get my wheels back next Friday. So today I went on a mad spending spree. Cush drive rubbers needed replaced, so got a set off ebay for £26.00. I have decided against putting rim tape on so I bought wheel decals (all red letter, but the "R" will be black)
I found a really good website for bearings http://www.bikebearings.co.uk full bearing kit for £46.00. I have decided to keep my original seat cowl so I bought a new one from powerbronze for £62.99. Mike is going to service the bike so I was looking for a service kit got K&N Air & Oil Filter off ebay for £54.00, fuel filter for £6.00 and 4 x NGK iridium ix spark plugs for £18.00 again off ebay. So hopefully the bike will be ready by the end of the month
I got the wheels off today, so I popped in past Mr Sillets and got the rubber removed then dropped the wheels off at Finesse to get powdercoated white. I should get my wheels back next Friday. So today I went on a mad spending spree. Cush drive rubbers needed replaced, so got a set off ebay for £26.00. I have decided against putting rim tape on so I bought wheel decals (all red letter, but the "R" will be black)
I found a really good website for bearings http://www.bikebearings.co.uk full bearing kit for £46.00. I have decided to keep my original seat cowl so I bought a new one from powerbronze for £62.99. Mike is going to service the bike so I was looking for a service kit got K&N Air & Oil Filter off ebay for £54.00, fuel filter for £6.00 and 4 x NGK iridium ix spark plugs for £18.00 again off ebay. So hopefully the bike will be ready by the end of the month
Last edited by Yamahahaha on Thu Feb 11, 2010 5:25 pm, edited 1 time in total.
- Gazza
- I don't believe it!
- Posts: 2475
- Joined: Mon Sep 10, 2001 1:00 am
- Current Ride: KTM 690 Duke
- Location: Sconny Botland
Re: My bike
Yamahahaha wrote:4 x NGK iridium ix spark plugs for £18.00 again off ebay.
The ebay spark plug factory
-
- Scary biscuits
- Posts: 147
- Joined: Sat Sep 19, 2009 4:23 am
- Current Ride: 2007 Yamaha R.1
- Location: Aberdeen
Re: My bike
Busy place, I noticed the QHSE Manager is missingGazza wrote:Yamahahaha wrote:4 x NGK iridium ix spark plugs for £18.00 again off ebay.
The ebay spark plug factory
- Grant
- Panty Granty
- Posts: 521
- Joined: Mon Jul 11, 2005 1:29 pm
Re: My bike
White wheels? To much effort to keep clean!
-
- Scary biscuits
- Posts: 147
- Joined: Sat Sep 19, 2009 4:23 am
- Current Ride: 2007 Yamaha R.1
- Location: Aberdeen
Re: My bike
As you said I am loaded, so I will pay someone to do it!!!Grant wrote:White wheels? To much effort to keep clean!
- Coddy
- Chavtastic!
- Posts: 920
- Joined: Sat May 21, 2005 2:54 am
- Current Ride: 2011 Ecosse Arr Waan SP Special.
- Location: I did see the speed limit officer, i just didn't see you....
Re: My bike
Please, don't put Arr Waan rim logo's on, if you have an R-6.
-
- Scary biscuits
- Posts: 147
- Joined: Sat Sep 19, 2009 4:23 am
- Current Ride: 2007 Yamaha R.1
- Location: Aberdeen
Re: My bike
The pic was an example. I have requested r.6 all red, but the "R" black, should look better than rim tape.Coddy wrote:Please, don't put Arr Waan rim tape on, if you have an R-6.
- Coddy
- Chavtastic!
- Posts: 920
- Joined: Sat May 21, 2005 2:54 am
- Current Ride: 2011 Ecosse Arr Waan SP Special.
- Location: I did see the speed limit officer, i just didn't see you....
Re: My bike
Should look good in red, but for me, i would change the FIAT logo for something else.
Don't like the look of a car logo on a bike, but it's your bike.
Don't like the look of a car logo on a bike, but it's your bike.
- Flamedamper
- Tube steak
- Posts: 79
- Joined: Sat May 30, 2009 10:29 am
- Current Ride: Gsxr 750
- Location: Skene, Aberdeenshire
Re: My bike
Sound's like it's going to look the part, the red does look nice, will one be getting a matching lid.
-
- Scary biscuits
- Posts: 147
- Joined: Sat Sep 19, 2009 4:23 am
- Current Ride: 2007 Yamaha R.1
- Location: Aberdeen
Re: My bike
No keeping the same lid.Flamedamper wrote:Sound's like it's going to look the part, the red does look nice, will one be getting a matching lid.
Update
Ordered the bearings on Monday and they arrived on Wednesday, very good service. Two items arrived today, fuel filter & cush drive rubbers very unusually as they came from eBay (user - bikebusiness). So just waiting for the filters and rim stickers to arrive. I also bought clear headlight lens covers as my headlight have a few scrapes, again off eBay.
- steve
- Tank Slapper
- Posts: 700
- Joined: Fri Dec 14, 2007 11:10 pm
- Current Ride: Hmmm I wonder
- Location: Here
Re: My bike
i think your bike will look pretty decent when its all rebuilt dude
all the best with your project
all the best with your project
-
- Scary biscuits
- Posts: 147
- Joined: Sat Sep 19, 2009 4:23 am
- Current Ride: 2007 Yamaha R.1
- Location: Aberdeen
Re: My bike
Cheers JT. Just looking forward to seeing the finished article. I wanted something different, so rather than the usual blue rossi rep I wanted it red. I can't see many having the same paint job.JT52 wrote:i think your bike will look pretty decent when its all rebuilt dude
all the best with your project
- splattercash
- Direct Access
- Posts: 25
- Joined: Tue Apr 29, 2008 3:05 pm
- Current Ride: Ducati 1098s
-
- Scary biscuits
- Posts: 147
- Joined: Sat Sep 19, 2009 4:23 am
- Current Ride: 2007 Yamaha R.1
- Location: Aberdeen
Re: My bike
Very nice.splattercash wrote:http://cgi.ebay.co.uk/Yamaha-YZF-R1-FIA ... 51904bba3d
should look good going by this one
-
- Scary biscuits
- Posts: 147
- Joined: Sat Sep 19, 2009 4:23 am
- Current Ride: 2007 Yamaha R.1
- Location: Aberdeen
Re: My bike
Spark plugs arrived today. Just waiting for the air & oil filter, clear headlight covers & new foot pegs.
-
- Scary biscuits
- Posts: 147
- Joined: Sat Sep 19, 2009 4:23 am
- Current Ride: 2007 Yamaha R.1
- Location: Aberdeen
Re: My bike
K&N Air & Oil Filters arrived today, also wheel decals & headlight lens covers. Finesse phoned to say the wheels are ready, so picked them up and dropped them off at Mike's to get the new bearings fitted. Once the new bearings are in and the brake disc's are back on its then down to Mr Sillet to get my rubbers back on. Once the wheels are back on the bike the paint jobby will begin.
- Grant
- Panty Granty
- Posts: 521
- Joined: Mon Jul 11, 2005 1:29 pm
Re: My bike
You need some red braided brake lines like the one on Ebay!
-
- Scary biscuits
- Posts: 147
- Joined: Sat Sep 19, 2009 4:23 am
- Current Ride: 2007 Yamaha R.1
- Location: Aberdeen
Re: My bike
The bike already had braided hoses, silver. Can you get covers???Grant wrote:You need some red braided brake lines like the one on Ebay!
- crankcase
- Tube steak
- Posts: 77
- Joined: Sun Aug 07, 2005 10:24 pm
- Current Ride: GSXR750k4
- Location: Under a stone
Re: My bike
Yamahahaha.
I used Finesse years ago to get a swing arm powder coated a silver gray colour. They did a superb job but the colour I thought was a bit flat.
How did your white wheels turn out ?
I'll be getting mine done the same colour as yours and am wondering how they'll look.
(Didn't bag off the brake line when I took the caliper offshore with me for a rebuild. Fluid on the rim for 3 weeks and you'll guess what happened next )
What did Finesse charge you for both wheels ?
I used Finesse years ago to get a swing arm powder coated a silver gray colour. They did a superb job but the colour I thought was a bit flat.
How did your white wheels turn out ?
I'll be getting mine done the same colour as yours and am wondering how they'll look.
(Didn't bag off the brake line when I took the caliper offshore with me for a rebuild. Fluid on the rim for 3 weeks and you'll guess what happened next )
What did Finesse charge you for both wheels ?
-
- Scary biscuits
- Posts: 147
- Joined: Sat Sep 19, 2009 4:23 am
- Current Ride: 2007 Yamaha R.1
- Location: Aberdeen
Re: My bike
Wheels look really good. They charged me £110 for 2 wheels and the hub carrier.crankcase wrote:Yamahahaha.
I used Finesse years ago to get a swing arm powder coated a silver gray colour. They did a superb job but the colour I thought was a bit flat.
How did your white wheels turn out ?
I'll be getting mine done the same colour as yours and am wondering how they'll look.
(Didn't bag off the brake line when I took the caliper offshore with me for a rebuild. Fluid on the rim for 3 weeks and you'll guess what happened next )
What did Finesse charge you for both wheels ?
- crankcase
- Tube steak
- Posts: 77
- Joined: Sun Aug 07, 2005 10:24 pm
- Current Ride: GSXR750k4
- Location: Under a stone
Re: My bike
Cheers min
-
- Scary biscuits
- Posts: 147
- Joined: Sat Sep 19, 2009 4:23 am
- Current Ride: 2007 Yamaha R.1
- Location: Aberdeen
Re: My bike
Get your bearings from http://www.bikebearings.co.uk mucho cheapocrankcase wrote:Cheers min
-
- Scary biscuits
- Posts: 147
- Joined: Sat Sep 19, 2009 4:23 am
- Current Ride: 2007 Yamaha R.1
- Location: Aberdeen
Re: My bike
Wheels have been rebuilt, so off to Mr Sillets to get my rubbers back on. Once the wheels are back on the bike the painting will begin. Should have a painted bike by next week, hopefully.
- crankcase
- Tube steak
- Posts: 77
- Joined: Sun Aug 07, 2005 10:24 pm
- Current Ride: GSXR750k4
- Location: Under a stone
Re: My bike
Ye I had a look at your link. Your supplying good info here minYamahahaha wrote:Get your bearings from http://www.bikebearings.co.uk mucho cheapocrankcase wrote:Cheers min
I'll be getting prices from there whenever I come to do the wheels. Nae idea when that'll be. Probably next winter but the bike will still be used this year. (Hope AberdeenBikers keep it slow for me on the viffer when I make my inaugural run)
I got one of the swing arm bearings from Scott bearings in Aberdeen. Can't remember how much it was but will probably get prices there too.
The other bearing was a non standard size (good old Honda ) and I ordered it through McGowans.
Again can't remember how much but do remember thinking OUCH.
- coullstar
- Bull Sh!tter
- Posts: 1058
- Joined: Thu Jun 16, 2005 12:04 am
- Location: Abz
Re: My bike
Get some of that paint protection film for the leading edges of your fairings. I had a bike that was painted and it chipped like a MOFO. A lot more than normal.
Not a race rep fan myself (although I did own one ) but it should look tidy from what youve said. At least there wont be another on the go....you hope.
Not a race rep fan myself (although I did own one ) but it should look tidy from what youve said. At least there wont be another on the go....you hope.