Finally stripped down my 1200 Blackbird engine last night to discover:
It needs a full set of valve stem seals
a couple of the shims are out of spec
the barrels are in pretty good nick
the Weisco pistons are in top nick
the crank and one of the Carrillo con rods are however toast .
The stem seals and shims are no problem
Does anyone know where I can buy Carrillo con rods in singles not as a (£800odd) set of 4?
Failing this does anyone know if its possible to have the crank and big ends reground and oversize shells fitted?
AW f*(&!!!
- CBRXX
- Tank Slapper
- Posts: 698
- Joined: Wed May 04, 2005 11:13 pm
- Current Ride: decisions decisions
- Location: almost there
- Coddy
- Chavtastic!
- Posts: 920
- Joined: Sat May 21, 2005 2:54 am
- Current Ride: 2011 Ecosse Arr Waan SP Special.
- Location: I did see the speed limit officer, i just didn't see you....
Re: AW f*(&!!!
Im not sure if Agra Engineering in Banff can do the crank. If they can, surely the big end would be possible to open out slightly for the bigger shells.
Imagine they do, as they regrind cams.
Imagine they do, as they regrind cams.
- CBRXX
- Tank Slapper
- Posts: 698
- Joined: Wed May 04, 2005 11:13 pm
- Current Ride: decisions decisions
- Location: almost there
Re: AW f*(&!!!
Cheers Coddy will give em a shoutCoddy wrote:Im not sure if Agra Engineering in Banff can do the crank. If they can, surely the big end would be possible to open out slightly for the bigger shells.
Imagine they do, as they regrind cams.
- IZINBARD
- Mr Angry
- Posts: 954
- Joined: Tue Sep 11, 2001 1:00 am
- Current Ride: GSXR 750 K6
- Location: Down in the dumps
- Contact:
Re: AW f*(&!!!
blackstorm wrote:Finally stripped down my 1200 Blackbird engine last night to discover:
It needs a full set of valve stem seals
a couple of the shims are out of spec
the barrels are in pretty good nick
the Weisco pistons are in top nick
the crank and one of the Carrillo con rods are however toast .
The stem seals and shims are no problem
Does anyone know where I can buy Carrillo con rods in singles not as a (£800odd) set of 4?
Failing this does anyone know if its possible to have the crank and big ends reground and oversize shells fitted?
TTS are the agents for Carrillo con rods in the U.K. but it takes forever to get stuff through them, 8 month for a set of pistons. You would be a lot quicker to buy direct from one of the big tuners in the states.
- Akrapovic
- ZZR1400.....Just like a Golf
- Posts: 1971
- Joined: Thu Mar 02, 2006 10:37 am
- Current Ride: ZX10R and MT-10.
- Location: Either grafting, down the pub, being a hermit or at a track-day.
- Contact:
Re: AW f*(&!!!
Bummer Gerry, how long do you think you will be off the road for mate?
- al
- Mass Debater
- Posts: 4768
- Joined: Wed Sep 05, 2001 1:00 am
- Current Ride: Space Hopper
- Location: Uranus
- Contact:
- al
- Mass Debater
- Posts: 4768
- Joined: Wed Sep 05, 2001 1:00 am
- Current Ride: Space Hopper
- Location: Uranus
- Contact:
- CBRXX
- Tank Slapper
- Posts: 698
- Joined: Wed May 04, 2005 11:13 pm
- Current Ride: decisions decisions
- Location: almost there
Re: AW f*(&!!!
Off the road !!!! have you taken leave of your senses man ??Akrapovic wrote:Bummer Gerry, how long do you think you will be off the road for mate?
just means I have to put up with the puny little 1137cc engine for a while longer till I get the proper phsyco engine fixed and back in
Got a bloke in the sates hopefully sorting me out with a crank and can get the rod direct from Carrillo for $400 these are not standard spec so will also probably have a fair old lead time, unfortunately I have to take the family on holiday in October so funds will not stretch till after christmas I thinks
- coullstar
- Bull Sh!tter
- Posts: 1058
- Joined: Thu Jun 16, 2005 12:04 am
- Location: Abz
Re: AW f*(&!!!
I was just going to say that the single rod will not be cheap but didnt expect that!!!blackstorm wrote:Off the road !!!! have you taken leave of your senses man ??Akrapovic wrote:Bummer Gerry, how long do you think you will be off the road for mate?
just means I have to put up with the puny little 1137cc engine for a while longer till I get the proper phsyco engine fixed and back in
Got a bloke in the sates hopefully sorting me out with a crank and can get the rod direct from Carrillo for $400 these are not standard spec so will also probably have a fair old lead time, unfortunately I have to take the family on holiday in October so funds will not stretch till after christmas I thinks